SECTION 1 - SYSTEM ARRIVAL
DANGER: THIS PRODUCT USES 220 VAC AND CAN CAUSE A FATAL
INJURY.
THE MANUAL ASSUMES AN EXPERIENCED ELECTRICIAN IS BEING
EMPLOYED. ALL ELECTRICAL WIRING MUST BE DONE IN ACCORDANCE WITH
THIS PRODUCT REQUIRES PVC CEMENT WELDING AND THE MANUAL
ASSUMES AN EXPERIENCED PLUMBER IS BEING EMPLOYED. DO NOT ACCEPT ANY
LEAKING PVC JOINTS. DO NOT “LEARN” PVC CEMENT WELDING ON THE
EXPENSIVE POOL VALVES PURCHASED. DAMAGE TO THE VALVES FROM POOR PVC
WELDING IS NOT COVERED BY THE MANUFACTURERS WARRANTY. ASSEMBLE
THE VALVES AND PIPES BEFORE WELDING TO MAKE SURE THEY FIT PROPERLY.
THIS IS CALLED A PRACTICE RUN BEFORE ACTUAL PVC CEMENT WELDING
OCCURS AND INSURES YOUR PARTS ARE READY FOR PERMANENT CEMENTING.
DO NOT USE DRAIN-WASTE (HOUSE SINK OR DRAIN) PVC FITTINGS (45º OR
90º ELBOWS, STRAIGHT SXS FITTINGS, ETC.) ON YOUR POOL’S SUPPORT SYSTEM
RE-ASSEMBLY. USE SCHEDULE 40 PVC FITTINGS. THE DRAIN-WASTE PVC
FITTINGS DO NOT HAVE THE SAME DEPTH OF PVC PIPE PENETRATION, WHICH
COULD RESULT IN THE POOL’S PVC PIPE POPPING AWAY FROM THE SHORTER
DRAIN-WASTE PVC FITTING (ELBOW, ETC.).
SECTION 1 - SYSTEM ARRIVAL
THE FINS ON THE PCS1 COIL ARE SHARP AND CAN CAUSE A
RAZOR- LIKE CUT IF YOUR HAND OR ARM COME INTO CONTACT WITH
THEM. TAKE APPROPRIATE CARE DURING INSTALLATION AND DO NOT
COME INTO DIRECT CONTACT WITH THE FINS OF THE COIL.IF THE COIL
FINS ARE ACCIDENTALLY DAMAGED, THEY CAN BE “COMBED” STRAIGHT WITH A
FIN COMB [10 FINS PER INCH].
THE PROTECTIVE GRILLE HAS SHARP EDGES WHICH CAN CUT YOUR
FINGER OR HANDS. EXERCISE CAUTION WHEN HANDLING, REMOVING OR
DO NOT OPERATE THE PCS1 WITH THE FAN GUARD PROTECTIVE
GRILLE REMOVED. THE PROTECTIVE GRILLE IS TO PREVENT HARM
WHILE THE FAN IS OPERATING. UNPLUG THE CONVECTION UNIT
[PCS1] DURING SERVICE AND ENSURE THAT THE FAN BLADE HAS
STOPPED ROTATING. IF THE FAN BLADE HAS BEEN CHANGED, ENSURE
THAT THE NEW BLADE IS TORQUED DOWN TO 120 INCH POUNDS AND
THAT LOCTITE HAS BEEN APPLIED TO THE THREADS OF THE LOCKING
SECTION 1 - SYSTEM ARRIVAL
DO NOT OPERATE THE MOTOR FOR AN EXTENDED TIME WITHOUT THE FAN
BLADE ATTACHED. THE MOTOR IS A “TOTALLY ENCLOSED AIR OVER” MOTOR
[TEAO] AND THE AIRFLOW OVER THE MOTOR FROM THE FAN BLADE PROVIDES
COOLING FOR THE MOTOR. OPERATING THE MOTOR WITHOUT THE FAN BLADE
ATTACHED WILL LEAD TO THE MOTOR OVER HEATING AND A THERMAL CUTOFF
OF THE MOTOR [INTERNALLY].
DO NOT REPLACE ANY SELF-TAPPING #10-1/2 TEKSSCREW USED ON
THE PCS1 REAR COIL SIDEWITH ANY SHEET METAL SCREW GREATER
THAN ONE-HALF INCH (1/2”) IN LENGTH. DOING SO CAN DAMAGE THE PCS1
WATER COIL BY PUNCTURING ONE OF THE COIL’S WATER PIPES OR MANIFOLDS.
THE PCS1 WEIGHS 240-253 LBS CRATED AND 135 LBS UNCRATED.
IN ADDITION, THE UNIT IS BULKY. CAUTION SHOULD BE TAKEN WHEN
LIFTING THE UNIT SO AS NOT TO TWIST FROM THE WAIST OR TO PLACE
A BURDEN ON THE LOW BACK. NO ATTEMPT SHOULD BE MADE TO LIFT
THE UNIT ALONE. TWO OR MORE MEN SHOULD BE PRESENT.
ATTEMPTING TO LIFT OR HANDLE THE PCS1 ALONE CAN LEAD TO
1-3
4-6
7-9
10-12
13-15
16-18
19-21
22-24
25-27
28-30
31-33
34-36
37-39
40-42
43-45
46-48
49-51
52-54
55-57
58-60
61-63
64-66
67-69
70-72
73-75
76-78
79-81
82-84
85-87
88-90
91-93
94-96
97-99
100-102
103-105
106-108
109-111
112-114
115-117
118-120
121
